|
Needed a drawing to figure out needed cables and connectors. Made this in PowerPoint, of all things!
Date: 07/22/2005
Views: 2966
|
Trencher almost done with 300 foot long trench, which will contain 8 runs of hardline, 3 runs of three conductor direct bury ele
Date: 12/17/2004
Views: 2382
|
Trench was about 3 feet deep. Trenching was done on December 16th, 2004, perhaps a day or two before the ground froze.
Date: 12/17/2004
Views: 2121
|
|
The house end of the trench. Radio room is behind window to the left. Two 4 inch PVC pipes going into the house can be seen to
Date: 12/17/2004
Views: 2147
|
Dick K0MN rolling out 4 inch drain tile that will be buried in trench.
Date: 12/17/2004
Views: 2395
|
Trencher finishes up his work, while ground crew finishes rolling out hardline.
Date: 12/17/2004
Views: 2066
|
|
My friend Gary from the phone company doing the trenching thing.
Date: 12/17/2004
Views: 1973
|
Ron N9OY, Mark N9UNW and Bill KE9XQ roll out some 3/4 inch CATV 75 ohm hardline (donated by local cable company)
Date: 12/17/2004
Views: 2026
|
View of front of the cable box, which is telephone company surplus. 4 inch PVC pipes that go into the closet near the radio room
Date: 06/11/2005
Views: 2360
|
|
Side view of cable box. Radio room is behind window on left side.
Date: 06/11/2005
Views: 2231
|
Back side of cable box. Have not backfilled yet.
Date: 06/11/2005
Views: 1853
|
Cut the hardline & drain tile just so it fit. Still have to install connectors, lightning protection, etc.
Date: 06/11/2005
Views: 2286
|
|
This is the box by the house, with feedlines and conduits from tower coming in. Poly Phaser lightning protectors are installed b
Date: 10/31/2005
Views: 1728
|
Close-up of the hardline coming from the tower, then transitioning to PolyPhaser lightning protectors, then to RG8-equiv into th
Date: 10/31/2005
Views: 1885
|
Mounted aluminum sheet to back of cabinet, then used aluminum channel (bent into L brackets and drilled) to mount the Polyphaser
Date: 06/04/2006
Views: 1512
|
|
Closeup of PolyPhasers mounted to aluminum sheet. Back row is all the 7/8" Andrew, and the front row is the 3/4" CATV
Date: 06/04/2006
Views: 1407
|
Another close-up of the PolyPhaser mounting, and the transition from hardline to RG-213.
Date: 06/04/2006
Views: 1383
|
All the cables are routed into the house via this 4 inch PVC. Big thanks to KB9YXV for cutting the hole in the box, and constru
Date: 06/04/2006
Views: 1153
|
|
I have two 4 inch holes in the house for cables, but only need one of them for now.
Date: 06/04/2006
Views: 1133
|
Another great telephone company relay box recycled for ham radio!
Date: 02/23/2006
Views: 1464
|
Big thanks to Terry KB9YXV for fashioning the tower mount for this box, and for punching the holes in the bottom of the box!!
Date: 02/23/2006
Views: 1394
|
|
Inside the box. FYI, those are 4-inch drain tile pipes that run from tower to house. Only one has anything in it so far.
Date: 02/23/2006
Views: 1886
|
|
|
